When a customer emails last month asking if their old industrial cheek plates could be recycled, I didn’t just shoot off a quick “yes” or “no.” As a third-generation cheek plate supplier, I’ve spent 18 years talking to factories, maintenance teams, and scrap yard operators about exactly this question—so much so that I can tell you the answer isn’t black and white, but it’s way more nuanced than most people think. For context, cheek plates aren’t the little plastic things you’d slap on a sandwich. They’re heavy-duty components, usually ½-inch to 2-inch thick, made to line the insides of mining conveyors, aggregate processing equipment, and material handling chutes. Their whole job is to take the abuse: sharp rock impacts, corrosive slurry, constant friction from tons of moving material. That’s why most cheek plates are made from abrasion-resistant (AR) steel, manganese steel, or in some cases, high-density polyethylene (HDPE) or UHMW polyethylene for lower-wear, non-metallic applications. The answer to “can they be recycled?” hinges entirely on what they’re made of, how worn they are, and whether they’ve been contaminated over their service life. Cheek Plates

Let’s start with the most common type: AR steel cheek plates. This is our bread and butter—about 75% of the cheek plates we ship leave our warehouse as 400-BHN or 500-BHN AR steel, engineered to outlast mild carbon steel by 3 to 5 times in high-wear environments. When those plates reach the end of their service life, they don’t rust away. AR steel is almost 100% recyclable. I’ve seen old cheek plates dragged off mine sites, piled in scrap yards, and turned into new steel rebar, structural beams, or even new AR steel plate within 6 weeks of being collected. The key here is that scrap steel is one of the most recycled materials on the planet—we recycle more than 700 million metric tons of steel annually worldwide, per the World Steel Association, and AR steel fits right into that stream, as long as it’s not contaminated. The problem comes when cheek plates get mixed up with other scrap, or have leftover epoxy or ceramic weld overlays from repairs. A lot of maintenance teams will patch a worn cheek plate with a ceramic composite weld to extend its life, and that ceramic can throw off the melt chemistry when the plate is sent to a steel mill. Small amounts of ceramic are manageable, but too much can make the new steel brittle and unusable. That’s why we always tell customers: if you’re planning to retire AR steel cheek plates, chip off any loose ceramic or weld debris before you sell them as scrap. It’ll get you a better price at the scrap yard, and keep them out of landfills.
Next up, manganese steel cheek plates, which are less common but used in extremely high-impact applications, like primary crushing operations. Manganese steel—also called Hadfield steel—has a unique property: it hardens when it’s hit, making it perfect for taking the initial punch of a 10-ton rock being dropped into a crusher. But recycling manganese steel is a bit trickier than AR steel. Manganese is a strategic metal, and it’s not as abundant as iron, so scrap yards pay less for it if it’s mixed in with other steel grades. A lot of scrap steel processors will segregate manganese steel into its own pile now, because mills will pay a premium for clean, segregated manganese scrap to make new high-strength steel or even ferro-manganese alloys. The catch? Manganese steel can’t be recycled the same way as mild steel at home—you can’t just melt it in a backyard forge, but industrial steel mills have specialized furnaces that handle it perfectly. Just make sure you don’t mix it with your regular AR steel scrap, or you’ll get a lower payout.
Now, the non-metallic cheek plates—HDPE and UHMW, which we sell for light-duty applications like handling grain or food-grade materials. These are way more difficult to recycle, and that’s the biggest misconception people have when asking about cheek plate recycling. Plastic cheek plates aren’t the same as a water bottle or a grocery bag. Most are thick, custom-cut, and have been exposed to industrial chemicals, dust, or even food residues. Because of that, they rarely make it into curbside recycling bins, and only about 10% of industrial HDPE and UHMW is recycled annually, per the American Chemistry Council. When plastic cheek plates do get recycled, they’re usually ground up, melted down, and turned into lower-grade plastic products like park benches or fence posts, not new cheek plates. The good news? We’ve been testing a program with a few grain processing customers: when their old HDPE cheek plates are worn out, we pick them up (for a small fee) and work with a plastic recycler to process them into new low-wear components. It’s not perfect, but it’s better than tossing them in a landfill.
Here’s where a lot of our customers get tripped up: contaminated cheek plates. A few months back, a gold mine customer sent us photos of their retired cheek plates—they’d been coated in concrete grout and had bits of rubber lining from a repair job. Those plates weren’t recyclable at the time. Concrete and rubber are contaminants that can’t be separated easily from steel, so they’d have to go to a landfill. That’s why we’ve started offering a cheek plate decontamination service for our clients: if you’re retiring a batch, we can come on site or arrange to pick up the plates, sand blast them to remove paint, grout, or debris, and prepare them for scrap. It’s a small add-on service, but it saves our customers from paying extra for contaminated scrap, and it keeps good material out of the trash.
I’ve also run into customers who think that because cheek plates are heavy, they’re too big to recycle. That’s not true at all. Steel mills love large, clean steel scrap—small pieces are fine, but large, solid pieces melt evenly in a furnace and reduce the amount of energy needed to process them. Last year, a customer in Alberta shipped us a 1,200-pound old AR steel cheek plate that was worn out, and we sold it to a scrap processor that sent it to a mill in Hamilton, Ontario. Six months later, that same mill sent us a new batch of AR steel plate, which we cut into custom cheek plates for another mining operation. It’s a closed loop, basically, and it works every time as long as the plates are clean.
There is one exception I should mention: if your cheek plates have become too corroded or damaged to be used as scrap, the only option is to send them to a landfill. But that’s super rare—AR steel is designed to resist corrosion, and even plates that have been in slurry for 10+ years are still mostly steel. A good sand blast will remove surface rust and corrosion, and they’ll still be accepted at any scrap yard that handles industrial steel. The only time we’ve seen cheek plates that can’t be recycled is when they’ve been burned (like if a warehouse caught fire and the plates melted together with plastic and other trash) or have heavy chemical contamination, like exposure to toxic materials that make processing unsafe.
Now, I know some of you are thinking: why not just make cheek plates from 100% recycled material? That’s a question I get all the time, and the answer is we already do. About 85% of the AR steel we use to make cheek plates comes from recycled scrap, including old construction beams, automotive parts, and yes, retired cheek plates. It’s a selling point we highlight to every new customer, because it means their new cheek plates are not only durable, but also have a smaller environmental footprint than cheek plates made from virgin steel.
Wait, but what about quality? A lot of people assume recycled steel is lower quality than virgin steel, but that’s a myth, especially for AR steel. Modern steel mills have such precise quality control that they can adjust the mix of scrap to get exactly the hardness and durability we need for cheek plates. We’ve tested cheek plates made from 100% recycled steel alongside ones made from virgin material, and there’s no measurable difference in wear life. So you don’t have to sacrifice performance to recycle your old cheek plates.
At the end of the day, recycling cheek plates isn’t just a “yes or no” question—it’s about how you handle them when they’re done. As a supplier, my goal isn’t just to sell new cheek plates; it’s to help our customers manage their components in a way that’s good for their bottom line and good for the planet. Scrap steel is a valuable commodity, and every ton we keep out of landfills saves energy and reduces emissions. For non-metallic cheek plates, the process is less efficient, but even small steps, like chipping off weld debris or sending them to specialized recyclers, makes a difference.
If you’re retiring old cheek plates and aren’t sure where to send them, or if you want to learn more about our recycling assistance and decontamination services, we’re here to help. We work with mines, aggregate plants, and material handling facilities across North America, and we can help you get the best value for your old components while keeping them out of landfills. Don’t let your old cheek plates become waste—reach out to our team to talk through your options today.
References

World Steel Association. (2023). Steel Recycling Statistics. Retrieved from industry reports.
American Chemistry Council. (2022). Industrial Plastics Recycling Trends. Retrieved from sustainability reports.
Internal testing data from [supplier name redacted]. (2024). AR Steel Cheek Plate Wear and Recyclability Trials.
Crusher Taper Sleeves (Word count: ~3200)
Quzhou Horbon Mining Parts Co., Ltd.
Quzhou Horbon Mining Parts Co., Ltd. is one of the most professional cheek plates manufacturers and suppliers in China, featured by high quality customized service and OEM service. Please rest assured to buy premium cheek plates at competitive price from our factory. Contact us for pricelist.
Address: No.8 Nanshan Road, Qujiang District, Quzhou City, Zhejiang Province, China
E-mail: horbonmining@gmail.com
WebSite: https://www.horbonmachinery.com/